Engineering tool for designing and checking hole and shaft fits. This tool allows you to calculate the nominal size and widest tolerance that guarantee your target clearance, transition or interference fit, check the worst-case fit between two existing parts, size housing and shaft fits for rolling bearings, and look up ISO 286 fits such as H7/g6.
Common questions about engineering fits and tolerances, and how to use the calculator above.
The Fit Calculator is a free, browser-based engineering tool for designing and checking hole and shaft fits. It finds the nominal size and tolerance a part needs to achieve a target clearance or interference, checks the worst-case fit of two existing parts, sizes housing and shaft fits for rolling bearings, and looks up ISO 286 fits such as H7/g6. It runs entirely in your browser, with nothing to install and no account needed.
The calculator uses worst-case limits, combining the opposite extremes of the two parts:
A positive value is a gap (clearance) and a negative value is an overlap (interference). If both values are positive the fit is a guaranteed clearance; if both are negative it is a guaranteed interference; otherwise it is a transition fit.
Enter the fit you need as a minimum and maximum clearance, then the dimensions of the part you already know. The tolerance available for the other part is the width of the target range minus the tolerance of the known part. For example, a shaft of Ø30 0/−0.010 mm with a target clearance of 0.005 to 0.025 mm leaves 0.020 − 0.010 = 0.010 mm for the hole, giving a recommended hole of Ø30.010 ±0.005 mm. The result is checked at every extreme, so any parts made within both tolerances will meet the target.
The widest allowable tolerance is rounded inward to the number of decimals shown, so the dimension can be written on a drawing exactly as displayed and still guarantee the fit. Rounding outward could break the target at the limits. If the result is too tight, increase the number of decimals in the header. The tool never recommends a zero tolerance, because a part cannot be made to an exact size.
Yes. Open More sizing options and enter the nominal in Lock nominal. The calculator then gives the widest tolerance around that size, which may be asymmetric, for example Ø30 +0.020/+0.005 mm for the hole in the example above. You can also place the nominal at the low or high end of the allowable range instead of the centre.
Choose Bearing Fit, enter the bearing's outside and bore diameters with their tolerances, and set a target fit for the housing pocket and for the shaft. Standard rolling bearings have both diameters toleranced 0/−x. The ring that rotates relative to the load usually needs an interference fit; for a rotating shaft in a stationary housing that is the inner ring on the shaft, while the outer ring has a clearance or transition fit in the housing. The calculator gives the pocket and shaft dimensions for your targets. Always confirm the fit with the bearing manufacturer's recommendations for your load, speed and temperature.
In an ISO 286 fit code, the capital letter describes the hole and the lower-case letter the shaft. The letter sets the position of the tolerance zone relative to the nominal size, and the number sets its width (the IT grade). H7/g6 is a common sliding clearance fit, H7/k6 a transition fit for location, and H7/p6 a light press fit. The ISO fits tool covers G7, H6, H7 and H8 holes with g6, h6, k6 and p6 shafts for diameters up to 30 mm, using the deviations tabulated in ISO 286-2. For example, Ø25 H7/g6 gives a clearance of 0.007 to 0.041 mm.
Yes. Switch Units to inches in the header. Calculations are always made at full precision, and the number of decimals can be set from 3 to 6. In inches, use at least four decimals, because three decimals resolve only 0.001 in (25.4 μm), which is too coarse for most fits.
Copy dimension copies the recommended dimension, such as Ø30.010 +0.005 / −0.005 mm, ready to paste into a drawing or note. Export JSON downloads your inputs as a file to your computer, and Import loads it again later. Your designs are never stored on our servers.
Yes. It is free to use in your browser, with no sign-up. It works on desktop, tablet and phone. The results are worst-case dimensional calculations; check surface finish, temperature and your manufacturing process capability before releasing a design.
© Me Virtuoso All Rights Reserved 2026